Book the 10-minute intro
For charging station manufacturers

Every charging station needs a payment display. Develop one, or license the one already in the field.

The OmniDisplay comes as a kit with hardware, firmware and PC software. It speaks Modbus RTU over RS-485. Your controller sends values, the display draws the QR code, the icons and the fonts itself.

Book the 10-minute intro
Video · OmniDisplay Video pending
RS-485 · Modbus Ships non-bootstrapped Designed in-house by Carsten Licence, not a service
How it connects

Two wires to your existing controller.

Charge controller your existing board RS-485 · MODBUS two wires OmniDisplay licensed from InTallyCon No changes to your controller. Two wires, one protocol.
Your controller sends values, not pixels.
In the field

Not a prototype. Shipping hardware.

1,000+
Charging stations running the reader
2
Products, one bus
10 min
Intro, free, run by Carsten
The decision

Developing it in house.
Or licensing it.

Developing it in houseLicensing from InTallyCon
Time to market
In houseTwelve to twenty-four months.

Schematic, layout, firmware, EMC, field testing. Then the first revision.

LicensedWeeks.

The design exists and runs. You integrate it into your controller.

Engineering cost
In houseA hardware engineer and a firmware engineer.

Both tied up for the whole period, and afterwards for maintenance.

LicensedOne licence fee.

The figure is on this page. No quote process, no per unit fee.

Field risk
In houseYour first revision is the field test.

Every fault surfaces at a customer site, not on your bench.

LicensedAlready in the field.

The reader runs in over a thousand charging stations today.

Certification
In houseYou carry it alone.

EMC, safety and the paperwork sit entirely on your side.

LicensedYou still carry it.

But you start from a design that has already been through it.

What you own
In houseEverything, eventually.

Including every revision, every erratum and every night of debugging.

LicensedAs much as you licence.

Production only, or with the hardware files, or with the firmware sources.

The product

One screen. Values in, QR code out.

OmniDisplay module

OmniDisplay

Designed by Carsten and in serial production. The kit contains hardware, firmware and the PC software you configure it with. The controller sends values, not pixels.

What the selling kit contains
  • 2 × OmniDisplay
  • 2 × terminal board
  • 2 × cable, one connector and open ends
  • USB to RS-485 converter (FTDI)
  • PC software via download link
Also from InTallyCon

RFBT001 RFID reader

If you also need card and tag reading on the station, there is a reader from the same house. It runs in over a thousand stations today, and there is a bundle price for both.

See the reader page
Licensing

Prices are on the table. No quote process.

Four tiers, three scopes. Pick the row that matches what you want to build and the column that matches how far it should reach.

OmniDisplayUSD · per licence
Licence scopeProduction+ Hardware+ Software+ HW + SW
Product4,2008,0008,00011,000
Product series5,90012,00012,00014,500
All products8,90016,00016,00022,000
Complete buy-out, stops us selling it to anyone else75,000 USD
Reader & DisplayUSD · per licence
Licence scopeProduction+ Hardware+ Software+ HW + SW
Product8,50016,50016,50022,500
Product series12,00023,00023,00029,500
All products17,50032,00032,00045,000
Complete buy-out, stops us selling it to anyone else150,000 USD
Additional service

Layout changes

Adaptations to the board layout for your enclosure or mounting. Hourly or fixed price.

Additional service

Firmware changes

Adaptations to the firmware for your protocol or your process. Hourly or fixed price.

All figures in USD. Deep dive: 250 USD per lesson, 50 USD per additional person. 50 % is credited against a licence.

How it works

Intro. Deep dive. Licence.

01

Intro

A short call with Carsten. You describe your station, he tells you whether the display fits and what integrating it involves. No slides.

Free
02

Deep dive

One hour per product, live on the PC software, every hardware and software feature. Booked per lesson.

250 USD per lesson · 50 USD per additional person
03

Licence

You pick tier and scope from the tables above. 50 % of what you spent on the deep dive is credited against the licence.

See the tables
Who is behind it

Carsten designed it. Carsten explains it.

Carsten Ziermann
Carsten Ziermann
Hardware & IoT cybersecurity · 30 years

He designed both the reader and the display. The reader runs in over a thousand charging stations. He runs the intro call and the deep dive sessions himself.

Igor Jakobencsuk
Igor Jakobencsuk
Software · controller side

Software and infrastructure. He signs off the technical side of every licence and is the contact once your engineers start integrating.

Questions

Before you book the call.

01Does it work with our charge controller?
It speaks Modbus RTU over RS-485. Your controller sends values, the display renders the QR code, the icons and the fonts itself. No graphics stack on the controller.
02How does the ad-hoc payment QR code work?
The display generates the QR code dynamically from the values your controller sends. What the code points to depends on your backend.
03What is in the kit?
Hardware, firmware and the PC software you configure the display with. The full list is in the product card above.
04Can we get exclusivity?
Yes, through a buy-out. The price is under each licence table.
05Can you adapt it to our enclosure or our protocol?
Yes. Layout and firmware changes are offered hourly or at a fixed price. Bring it to the intro.
06What does it cost?
The licence prices are on this page, by tier and scope. The intro is free, the deep dive is 250 USD per lesson and half of it is credited against a licence.
07What does non-bootstrapped delivery mean?
The reader is delivered in non-bootstrapped mode. What that means for your production line is part of the deep dive. Wording to be confirmed by Carsten.
08Do you also offer a reader?
Yes. The RFBT001 comes from the same house, uses the same bus and runs in over a thousand charging stations. There is a bundle price for reader and display in the second table above. See the reader page.
Next step

Ten minutes. Then you know.

A short call with Carsten. You tell him what you are building, he tells you whether this fits. If it does not, he will say so.

Book the 10-minute intro